柱式液压平板硫化机校准规范（试验报告）.docx

《柱式液压平板硫化机校准规范（试验报告）.docx》由会员分享，可在线阅读，更多相关《柱式液压平板硫化机校准规范（试验报告）.docx（17页珍藏版）》请在第壹文秘上搜索。

1、JJF湖南省地方计量校准规范JJF（湘）-柱式液压平板硫化机校准规范Ca1.ibrationSpecificationforCo1.umnHydrau1.icTypeF1.atVu1.canizingMachine（试验报告）柱式液压平板硫化机试验报告一.实验目的本规范对柱式液压平板硫化机的校准方法进行了规定，本次试验涉及5个厂家到6台不同型号的设备验证校准方法和校准规范的可行性。二.实验情况本次试验的样品主要选取使用厂家在生产中广泛使用的产品和生产厂商反馈的主流产品，项目组按拟定规范的试验方法进行试验，分别选取浙江东毓、磐石精密工业、湖南华意、青岛亚华、青岛沃能的产品进行现场试验。同时项目组

2、针对温度采用了表面温度计进行测量,其偏差和重复性远不如规范中所选用的方法；针对平行度采用百分表进行测量，试验效果不佳，无法满足反应压实平行度测量的要求。三.比较和结论从试验过程和数据来看，规范中的校准方法简单易学且效率高，获得使用方的高度认可,绝大部分计量器具符合拟定规范对计量特性的要求，说明规范适用性良好。对数据进行分析,热板尺寸对温度和平行度参数的影响较为明显，但热板尺寸大时温度偏差和平行度较大，且对平行度影响更大。型号规格：HY1.-2000P出厂编号：63572生产厂家：衡阳华意热板尺寸：2000*20001、温度参数校准上加热板温度设定值：150（单位：。C）实测温度值1234567

3、891151.26152.12150.36152.38150.94151.78152.41151.03151.462151.38152.19150.46152.39151.06151.86152.57151.21151.523151.49152.27150.58152.57151.14152.02152.65151.38151.674151.57152.43150.66152.65151.22152.08152.71151.46151.755151.65152.48150.74152.73151.3152.16152.79151.54151.836151.73152.56150.82152.8

4、1151.38152.24152.87151.62151.91最大值151.73152.56150.82152.81151.38152.24152.87151.62151.91最小值151.26152.12150.36152.38150.94151.78152.41151.03151.46上偏差2.87下偏差-0.64均匀性2.06波动度0.30下加热板温度设定值：160（单位：C）实测温度值1234567891162.07162.33162.20161.94162.35162.67162.85162.06162.442162.10162.51162.21161.96161.98162.001

5、62.03162.17162.333162.25162.34162.00161.89162.37162.37162.78162.06162.304162.32162.32162.10161.97162.16162.63162.32162.61162.795162.40162.52162.07161.70161.99162.13162.80162.01162.206162.43162.90162.44162.22162.64162.02162.37162.67162.70最大值162.43162.90162.44162.22162.64162.67162.78162.67162.79最小值162

6、.07162.32162.00161.70161.98162.00162.03162.01162.33上偏差2.79下偏差1.70均匀性1.37波动度+0.752、加压平行度校准（单位：mm）加压后厚度平行度123456789101.181.201.291.351.351.311.211.211.151.140.283、计时器误差参数校准（单位：S）设定值实测1实测2实测3平均值示值误差900.00899.66897.79897.75898.401.60柱式液压平板硫化机校准原始记录（2）上加热板温度设定值：120（单位：。C）实测温度值1234567891119.49119.65119.49

7、119.21119.39119.74120.35120.59120.712119.61119.99119.77119.73120.07120.12120.21120.31120.683119.62120.01119.94119.90120.28120.41121.07121.15121.454119.67119.84119.64119.28119.58119.80120.46120.70120.885119.86120.00119.92119.72119.75120.09120.63120.91121.346119.91120.30120.29120.23120.54120.79121.171

8、21.45121.52最大值119.91120.30120.29120.23120.54120.79121.17121.45121.52最小值119.49119.65119.49119.21119.39119.74120.21120.31120.68上偏差1.52下偏差-0.79均匀性1.54波动度0.57下加热板温度设定值：140（单位：C）实测温度值1234567891140.78141.15140.97140.75141.23141.27141.84141.93142.222140.98141.23140.75140.54140.91141.06141.57141.75142.02314

9、1.11141.16140.70140.49140.56140.58141.19141.44141.804141.18141.54141.08140.71140.96141.00141.42141.56142.025141.31141.66141.47141.27141.48141.80142.25142.28142.456141.49141.64141.27141.00141.24141.61141.90142.00142.27最大值141.49141.66141.47141.27141.48141.80142.25142.28142.45最小值140.78141.15140.70140.4

10、9140.56140.58141.19141.44141.80上偏差2.45下偏差0.49均匀性1.34波动度+0.612、加压平行度校准（庠1.位:mm)加压后厚度平行度123456789101.081.111.141.221.221.211.121.091.151.220.143、计时器误差参数校准（单位：S）设定值实测1实测2实测3平均值示值误差900.00901.40900.23902.65901.43-1.43热板尺寸：1200*1400型号规格：HY1.-100Op出厂编号：92185生产厂家：衡阳华意1、温度参数校准型号规格：X1.B-3MN出厂编号：201.10066生产厂家：

11、青岛亚华热板尺寸：1500*15001、温度参数校准上加热板温度设定值：180（单位：。C）实测温度值1234567891178.86179.10178.70178.48178.73178.92179.50179.50179.552179.04179.42179.07178.78179.10179.53180.12180.29180.323179.23179.57179.57179.24179.24179.42180.09180.24180.654179.31179.56179.49179.31179.31179.47179.94180.10180.425179.46179.53179.381

12、78.90179.03179.15179.67179.73179.976179.46179.65179.30179.13179.46179.50179.95180.19180.20最大值179.46179.65179.57179.31179.46179.53180.12180.29180.65最小值178.86179.10178.70178.48178.73178.92179.50179.50179.55上偏差0.65下偏差-1.52均匀性1.22波动度0.55下加热板温度设定值：180（单位：C）实测温度值1234567891180.67180.77180.64180.24180.36180.41180.93181.09181.102180.84181.20181.16180.88180.93181.23181.26181.52181.753180.94181.44181.261